- Published on
It wasn't a big move, but we finally headed out of Port LaBelle Marina for our next destination – the LaBelle town docks. It was only 3 miles and one opening bridge away, but at least we had cast off the dock lines. We made a couple of more significant improvements to the boat before heading out and even managed to make a trip to Cape Coral for a great Thanksgiving with “family”.
Solar Upgrade
They are thin and light. Four of them produce the same wattage as all five of the panels Orion Jr sported last season. These are our new semi-flexible solar panels that we installed on the bimini shortly after arriving at LaBelle. After considering various options, we opted for 2- 30W and 2 – 90W panels, which are mounted on the bimini on each side of the boom. Given the different dimensions of the new panels, we had to modify the bimini attachment points and create a new channel to allow the wires and thicker MC4 connections to pass over the bimini and down to the solar controller mounted in the port cockpit locker. They also have a blocking diode that ensures the current flows toward the batteries from the panels, but not the other way around. The only downside of the new panels is that they are not as shade-tolerant as the 3 flexible panels that used to sit atop the bimini. So, we needed to ensure they were mounted as far from the boom as possible to minimize shade, and also we needed to expect that we would routinely lose half of the panels, assuming the boom cast a shadow in one direction or the other.
They are thin and light. Four of them produce the same wattage as all five of the panels Orion Jr sported last season. These are our new semi-flexible solar panels that we installed on the bimini shortly after arriving at LaBelle. After considering various options, we opted for 2- 30W and 2 – 90W panels, which are mounted on the bimini on each side of the boom. Given the different dimensions of the new panels, we had to modify the bimini attachment points and create a new channel to allow the wires and thicker MC4 connections to pass over the bimini and down to the solar controller mounted in the port cockpit locker. They also have a blocking diode that ensures the current flows toward the batteries from the panels, but not the other way around. The only downside of the new panels is that they are not as shade-tolerant as the 3 flexible panels that used to sit atop the bimini. So, we needed to ensure they were mounted as far from the boom as possible to minimize shade, and also we needed to expect that we would routinely lose half of the panels, assuming the boom cast a shadow in one direction or the other.
Once Cathy modified the bimini to accept the panels, Dave mounted them, simply using wire ties to attach them to the new webbing strips – a much simpler process than the complicated tie-down used before. He then used some Y-connectors and T-connectors to join the panels to each other and route them to the solar controller in the port cockpit locker. Once in place, the panels were working great. Since we hadn't yet removed the 2 rigid panels that sat on the PVC arch, the 6 panels together were keeping up with our usage enough that we didn't need to run the Honda generator for days at a time. Eventually, we'll remove the arch and sell the two panels mounted there. In the meantime, we're flush with power – as long as the days are sunny.
More Boat Stuff
Keeping up with the Joneses. As Cathy did some repairs and sewing for other cruisers, Dave kept coming up with ideas for Jr to keep up. Why don't we have a tiller cover? Maybe we'd get more air flow with another set of larger mesh screens? OK. OK. So, in short order, a tiller cover appeared and this one even had a webbing strap to hold the tiller up and out of the way in the cockpit. And that 2nd set of screens appeared. With the warm weather and the persistent bugs, the increased air flow while still keeping the pests at bay was appreciated.
Keeping up with the Joneses. As Cathy did some repairs and sewing for other cruisers, Dave kept coming up with ideas for Jr to keep up. Why don't we have a tiller cover? Maybe we'd get more air flow with another set of larger mesh screens? OK. OK. So, in short order, a tiller cover appeared and this one even had a webbing strap to hold the tiller up and out of the way in the cockpit. And that 2nd set of screens appeared. With the warm weather and the persistent bugs, the increased air flow while still keeping the pests at bay was appreciated.
In the meantime, Dave kept busy with his own projects. He installed quick-disconnects on the fuel tanks, so that they can be removed without using a tool. This makes them more compliant with Coast Guard regulations. Despite our best efforts in the spring, several dock lines spent a lot of their time over the summer in the water. So, one by one, he soaked and scrubbed them to remove the growth and associated smell. We decided to move the sewing machine off the boat, storing it now in the truck. That meant we no longer had anything to serve as a backstop on the shelf it previously occupied, allowing our clothes to fall down behind the shelf on the floor. So Dave found a way to extend the existing shelf, epoxying a support against the hull, and then simply cutting a foam board to fit into the gap. It works well. No more clothes on the floor.
We continued to work to clean up the boat's exterior. Dave cleaned the stain off the waterline, and then we worked together to wax the hull. Cathy waxed the upper deck to restore and protect it as well. After mulling over the problem for a while, Dave came up with a new solution to the problem of protecting the toe rail from the anchor chain paying out over it as it is deployed or retrieved. Using a length of PVC and flexible hose and a few cable ties, he sandwiched the toe rail between the 2 tubes, creating a bridge that might be able to protect it. We'll see how it works when we anchor for the first time.
Finally, we had to make a repair to the hinge on the forward hatch, once Cathy opened it one morning only to discover that it was swinging wildly, since one hinge had broken in half. We had purchased a replacement hinge two years ago, since the one hinge had a crack in it, but this was the first time we had reason to actually fit it in place. The footprint looked really close, but was it exactly the same? Apparently so. We managed to fit the new hinges in place, but unfortunately, we didn't have exactly the right length bolts. (The predecessors had been cut off to get the right length.) So, the hinges work well for now, but we'll have to keep looking for the unusual size bolts to do the installation right.
The hinge wasn't the only emergency repair that we had to do. Our short trip to LaBelle was more eventful than it should have been because the engine kept shutting down. We switched fuel tanks and it then ran smoothly. The problem was two pinch points in the fuel hose on the one tank. Dave replaced the hose and the engine ran smoothly on both tanks again. The summer heat once again caused 2 wooden blocks that we had epoxied to the hull to support the water tank and to support the dinghy seats to fall off. We replaced them taking more care to clean and sand both the block and the hull surface to get a better bond. Maybe we got it right this time. Cathy loves crawling into that locker to fix these things, so she's especially hopeful they stay put.
The hinge wasn't the only emergency repair that we had to do. Our short trip to LaBelle was more eventful than it should have been because the engine kept shutting down. We switched fuel tanks and it then ran smoothly. The problem was two pinch points in the fuel hose on the one tank. Dave replaced the hose and the engine ran smoothly on both tanks again. The summer heat once again caused 2 wooden blocks that we had epoxied to the hull to support the water tank and to support the dinghy seats to fall off. We replaced them taking more care to clean and sand both the block and the hull surface to get a better bond. Maybe we got it right this time. Cathy loves crawling into that locker to fix these things, so she's especially hopeful they stay put.
Turkey Day and more
Our departure from Port LaBelle was delayed longer than we had hoped due to the windy weather brought by a cold front Thanksgiving week. The same front that brought cold and lousy weather to much of the rest of the country. We didn't let it de-rail our plans too much. Instead we drove to Tom and Dau's house for Thanksgiving dinner, spending the day with them, their son Grady, Dau's mom and step-dad and Dau's sister and brother-in-law. It was a big family gathering and we felt privileged to be able to join all of Cathy's “cousins” for the day.
Our departure from Port LaBelle was delayed longer than we had hoped due to the windy weather brought by a cold front Thanksgiving week. The same front that brought cold and lousy weather to much of the rest of the country. We didn't let it de-rail our plans too much. Instead we drove to Tom and Dau's house for Thanksgiving dinner, spending the day with them, their son Grady, Dau's mom and step-dad and Dau's sister and brother-in-law. It was a big family gathering and we felt privileged to be able to join all of Cathy's “cousins” for the day.
Before heading to Cape Coral for the holiday dinner, we stopped by the Harold Curtis Honey store to check out a local honey producer. We got to spend some time talking to the proprietor, learning how their honey is made and the intricacies of managing the hives. It was an interesting discussion, and we left with some delicious honey to take to Tom and Dau's.
As we provisioned the boat, we discovered a wonderful Farmer's Market in town on Saturdays. In addition to some fresh produce (including some huge Florida avocados), there was fresh bread, and the best tacos we've ever had. We tried enchiladas made the way native Mexicans eat them, with lettuce, diced carrots and potatoes and sour cream on top. Then there was the “fruit cup” stand, which always had a line. We bought one, declining their offer to top it with chili pepper, but accepted the salt and lime. The combination of melon, chunks of fresh coconut, pineapple, cucumber, some crunchy white stuff --- it was all good. Needless to say, we made sure we made it back for a 2nd trip.
Where to?
So, we keep figuring out where we're headed on our cruise. Since we plan to leave the boat back at Port LaBelle when we travel north for Christmas, we'll only be out and about for a couple of weeks. Maybe we'll head to Cayo Costa or Fort Myers Beach. We've already promised Tom and Dau that we'll come back by boat. And then there's Franklin Lock. We're not in a hurry, so it will give us time to explore. And at least we're moving again.
So, we keep figuring out where we're headed on our cruise. Since we plan to leave the boat back at Port LaBelle when we travel north for Christmas, we'll only be out and about for a couple of weeks. Maybe we'll head to Cayo Costa or Fort Myers Beach. We've already promised Tom and Dau that we'll come back by boat. And then there's Franklin Lock. We're not in a hurry, so it will give us time to explore. And at least we're moving again.
- Published on
After a couple of days on the road, we once again arrived in LaBelle on election day. The boat was in pretty good shape, so we started the re-commissioning process that is going more smoothly the 2nd time around. With a truck available to us, routine trips to town made re-provisioning easier and also let us take in some local dining and festivals.
Starting Up Jr
We heard from our neighbors here in LaBelle that this was a very wet summer. Water levels in Lake Okeechobee were so high that they had to open the locks to let water flow out in order to reduce the level. Pretty big change from concerns about water so low that the waterway was closed a few years ago. At any rate, we were concerned about how much water had made its way into the boat over the summer. Although we had re-sealed a number of problem areas, there wasn't much time to prove them out while we were still on the boat in the spring. So, with a mental drum roll, we unlocked the companionway and peered inside.
It wasn't too bad.
The boat smelled OK, and the floor was dry. There was evidence that water had come in, but nothing appeared damaged by it. It's hard to say whether the water that did make it inside came from the companionway or our problem portlight, since it was centered in the Main Saloon. However, the forward compartments were dry, meaning that we had had some success in fixing those leaks.
So, we set to work pulling all of the stuff out of the interior: rudder, dinghy, outboard, boom, stackpack, bimini, enclosure, etc. We pulled out enough to get some work done on deck and then closed up the boat to fog the interior one last time. While the boat was fogging, we rigged the boom, hung the rudder, mounted the dinghy outboard. By the end of the day, the bimini was up, the dinghy was in the water, and we had the boat cleaned and outfitted enough that we could sleep down below.
We heard from our neighbors here in LaBelle that this was a very wet summer. Water levels in Lake Okeechobee were so high that they had to open the locks to let water flow out in order to reduce the level. Pretty big change from concerns about water so low that the waterway was closed a few years ago. At any rate, we were concerned about how much water had made its way into the boat over the summer. Although we had re-sealed a number of problem areas, there wasn't much time to prove them out while we were still on the boat in the spring. So, with a mental drum roll, we unlocked the companionway and peered inside.
It wasn't too bad.
The boat smelled OK, and the floor was dry. There was evidence that water had come in, but nothing appeared damaged by it. It's hard to say whether the water that did make it inside came from the companionway or our problem portlight, since it was centered in the Main Saloon. However, the forward compartments were dry, meaning that we had had some success in fixing those leaks.
So, we set to work pulling all of the stuff out of the interior: rudder, dinghy, outboard, boom, stackpack, bimini, enclosure, etc. We pulled out enough to get some work done on deck and then closed up the boat to fog the interior one last time. While the boat was fogging, we rigged the boom, hung the rudder, mounted the dinghy outboard. By the end of the day, the bimini was up, the dinghy was in the water, and we had the boat cleaned and outfitted enough that we could sleep down below.
This was a much warmer November than last year, so we paced ourselves in restoring order over the next few days, trying to moderate what we did in the heat. However, by the end of our first week, the sails and stackpack were hung, the Nissan outboard was back in place and running, the composting head had its compost in place, and the water system was in the process of being primed for use with a heavy dose of bleach. We were close to having all the systems up and running. Cathy used up the super-chlorinated water to clean the deck and Dave used some to clean the lines that had spent a little too much time in the water. Once the tank ran dry, we filled it up again and began using the water for drinking and cooking as well.
The only real surprise in all of this activity came on our 2nd day, when Cathy lifted up the seat to access the fuel locker and a wasp's nest was staring her in the face, with most of its residents at home. By nightfall, they came to an unfortunate end. There's not enough room on Jr for all of us, so they had to go.
The only real surprise in all of this activity came on our 2nd day, when Cathy lifted up the seat to access the fuel locker and a wasp's nest was staring her in the face, with most of its residents at home. By nightfall, they came to an unfortunate end. There's not enough room on Jr for all of us, so they had to go.
Boat Projects
We had a number of projects planned for improvements when we returned to the boat, many of which were underway before we left Hampton.
The wooden block on Jr's motor mount for the Nissan looked worn and peeling, which made Dave doubt its integrity. The last thing we wanted to have happen was to lose the outboard due to a cracked motor mount support. So, after researching possible replacements from the manufacturer, which were very expensive, we decided to try making our own. With Steve's help, Dave cut 3 rectangles of 5/8” plywood to the dimensions of the existing motor mount. He then epoxied them together, and sanded the edges flush. Cathy took over and varnished the block of wood to protect it from the inevitable abuse once it was employed.
When we arrived in LaBelle, Dave removed the old board and used it to locate and drill the holes in the new block for the mounting bolts. He oversized the holes so he could fill them with epoxy and drill again, protecting the inside of the holes from the elements. Since we lacked any sophisticated wordworking tools, Dave wasn't able to exactly replicate the recessed hardware of the original installation. But with careful measuring, he was able to ensure the outboard would slip between the new bolts, which would otherwise get in the way.
Sure enough, the Nissan slid into place with only a fraction of an inch to spare either way. With so much invested, we will make sure this mount doesn't deteriorate like its predecessor.
We had a number of projects planned for improvements when we returned to the boat, many of which were underway before we left Hampton.
The wooden block on Jr's motor mount for the Nissan looked worn and peeling, which made Dave doubt its integrity. The last thing we wanted to have happen was to lose the outboard due to a cracked motor mount support. So, after researching possible replacements from the manufacturer, which were very expensive, we decided to try making our own. With Steve's help, Dave cut 3 rectangles of 5/8” plywood to the dimensions of the existing motor mount. He then epoxied them together, and sanded the edges flush. Cathy took over and varnished the block of wood to protect it from the inevitable abuse once it was employed.
When we arrived in LaBelle, Dave removed the old board and used it to locate and drill the holes in the new block for the mounting bolts. He oversized the holes so he could fill them with epoxy and drill again, protecting the inside of the holes from the elements. Since we lacked any sophisticated wordworking tools, Dave wasn't able to exactly replicate the recessed hardware of the original installation. But with careful measuring, he was able to ensure the outboard would slip between the new bolts, which would otherwise get in the way.
Sure enough, the Nissan slid into place with only a fraction of an inch to spare either way. With so much invested, we will make sure this mount doesn't deteriorate like its predecessor.
When we arrived in LaBelle, Dave removed the old board and used it to locate and drill the holes in the new block for the mounting bolts. He oversized the holes so he could fill them with epoxy and drill again, protecting the inside of the holes from the elements. Since we lacked any sophisticated wordworking tools, Dave wasn't able to exactly replicate the recessed hardware of the original installation. But with careful measuring, he was able to ensure the outboard would slip between the new bolts, which would otherwise get in the way.
Sure enough, the Nissan slid into place with only a fraction of an inch to spare either way. With so much invested, we will make sure this mount doesn't deteriorate like its predecessor.
Sure enough, the Nissan slid into place with only a fraction of an inch to spare either way. With so much invested, we will make sure this mount doesn't deteriorate like its predecessor.
Before leaving Hampton, Dave ordered some new LED light bulbs and a new fixture for the Main Saloon. We had never upgraded the fixtures in Orion Jr's head and V-berth to LED, so the new bulbs were going to fit in there. As for the Main Saloon, the existing 40 LED strip was having some bulb failures. So, the fixture was intended to replace it. Since we didn't remember exactly what the bulb bases looked like for the head and V-berth, it was a bit of luck that Dave ordered the correct bulbs to plug into these fixtures. Replacing the fixture in the Main Saloon was pretty straightforward and now the light from the new fixture is dramatically bright, allowing us to read easily under it. An improvement with the new fixture over the old is that it has a voltage regulator that allows the LED's to tolerate a large range of voltages from 8 to 30V without damage.
New LED bulb in V-berth
Exploring LaBelle and Points West
20131109_130348 Dave talking to someone at Hendry Co Heritage Festival
We stumbled across a number of activities in LaBelle that we missed last year. The first Hendry County Heritage Festival was held at the local rodeo grounds. It had a mixture of local history, craft vendors, non-profits and produce booths. From fossils to the progression of voting boxes, we learned a bit and had some good conversation and some good food. We also got to meet more of our fellow cruisers who have re-joined their boats in the marina, gathering more routinely under the trees at the marina office.
We made our annual provisioning run into Fort Myers, but this time found a new marine parts store in the Marine Trading Post, located in North Fort Myers. It was full of new and used marine parts, allowing us to locate some more hard-to-find components and supplies.
Cathy's sewing skills were in demand as she did some repairs and make a tiller cover for a neighboring boat.
So, we still have one or two more projects to complete, but Orion Jr could be ready to go at any time. In the meantime, we are enjoying the company of our neighbors and the opportunities to explore LaBelle a little more than we did last year.
20131109_130348 Dave talking to someone at Hendry Co Heritage Festival
We stumbled across a number of activities in LaBelle that we missed last year. The first Hendry County Heritage Festival was held at the local rodeo grounds. It had a mixture of local history, craft vendors, non-profits and produce booths. From fossils to the progression of voting boxes, we learned a bit and had some good conversation and some good food. We also got to meet more of our fellow cruisers who have re-joined their boats in the marina, gathering more routinely under the trees at the marina office.
We made our annual provisioning run into Fort Myers, but this time found a new marine parts store in the Marine Trading Post, located in North Fort Myers. It was full of new and used marine parts, allowing us to locate some more hard-to-find components and supplies.
Cathy's sewing skills were in demand as she did some repairs and make a tiller cover for a neighboring boat.
So, we still have one or two more projects to complete, but Orion Jr could be ready to go at any time. In the meantime, we are enjoying the company of our neighbors and the opportunities to explore LaBelle a little more than we did last year.
Parting Shots
A lightning storm hit the marina not long before we arrived and this catamaran took a direct hit and caught fire. Thanks to some quick action by a fellow cruiser and some local off-duty firefighters, the dock and the rest of the boats in our basin were spared. But not so with this boat, ironically named, David's Wings.
A lightning storm hit the marina not long before we arrived and this catamaran took a direct hit and caught fire. Thanks to some quick action by a fellow cruiser and some local off-duty firefighters, the dock and the rest of the boats in our basin were spared. But not so with this boat, ironically named, David's Wings.
The pilings where the cat was berthed show the intensity of the fire.